Topmove Luggage Rack A Manuel d'utilisateur télécharger pdf (Page 14)

16 GB/MT

Assembly

1. Inserts (Fig. B)

Choose from the following options in accor-

dance with the diameter of your saddle post or

the handlebar stem:

• For a diameter of 24-26mm mount both

inserts (3) on the adapter (4) and the adapter

counter piece (1).

• For a diameter of 26-29mm mount one insert

on the adapter.

• For a diameter of 29-31mm do not mount any

inserts.

2. Mount the adapter on the handle-

bar or saddle post (Fig. C and D)

Fasten the adapter and the adapter counter

piece with 4 x screws, long (2), to the handlebar

or saddle post.

Tightening force: 4 newton metres

3. Adjust angle

Loosen the adjusting screw (4a) on the adapter

with the tool (11) (Fig. E), to adjust the angle of

the adapter (Fig. F). Next, re-tighten the adju-

sting screw (Fig. E).

Tightening force: 4 newton metres

4. Assemble and position adapter

ﬁxture

Before assembling, make sure the

luggage rack (8) can be fastened to the

adapter with the short or the long side.

Decide which way you would like to

mount the product before assembling

the adapter ﬁxture (6). Make sure that

the notch (6a) on the adapter ﬁxture is

facing down (Fig. G).

Fasten the adapter and the adapter ﬁxture

counter piece (7) with 3 x screws, short (5) in

the areas speciﬁed (Fig. H).

Tightening force: 4 newton metres

Do not fully tighten the screws yet.

You can still shift the adapter on the

braces of the luggage rack as required

(Fig. H).

After you have set the ﬁnal position, tighten the

screws.

5. Connect the luggage rack with

the adapter (Fig. I)

Insert the adapter ﬁxture (6) in the opening

provided on the adapter (4). Following this, test

whether the luggage rack is securely locked in

the adapter by pulling on it.

6. Assemble fastening strap (Fig. J)

Lay the ends of the strap (9d) around the lugga-

ge rack frame from above and pull the ends of

the strap with the edge from behind through the

strap-system slots (9c). Lower the strap ends (9d)

into the notches of the strap system.

Note: make sure that the logo (9b) is

facing upwards.

Hitch the strap grip (9a) onto the other end of

the frame.

7. Loading the product

a) Pull the strap grip (9a) from the luggage rack

frame (Fig. K).

b) Use the strap system (9c) to set the appropri-

ate strap length (Fig. L).

c) Load the product and pull the fastening strap

by pulling it over the load (Fig. M).

d) Fasten the strap grip (9a) to the frame so that

the load is fastened to the product (Fig. N).

8. Extra security with the expander

band

Set the length of the expander band (10) using

the buckle (10a). Fasten the load further with

the expander band by fastening the ends of the

expander band (10b) to the frame over the load

on the left and the right (Fig. O).

Lighting

No lighting is included with this article. You can

buy reﬂectors and back lights in specialist shops

that can be attached with a fastener.

These are mounted on the frame of the luggage

rack (Fig. P).

Remove article

Remove the load and press the unlocking button

(6b) in order to release the luggage rack from

the adapter (Fig. Q).

1 2 ... 9 10 11 12 13 14 15 16 17 18

Commentaires sur ces manuels

Pas de commentaire